mccalls 6172 progress

I managed to make solid¬†progress on my blazer last week (Mccalls 6172), and I’m pretty thrilled with how it is turning out! There is very little in the pattern I’ve felt the need to change or improve upon, so if you’re in the market for a blazer pattern, this one is a winner. I especially love that it will work in a variety of fabrics (structured or not) and there are options for different lengths (cropped to hip length). Also, it has a lot of built in lines for pattern alterations and instructions for many common adjustments. Very handy! As per usual, there are only directions for FBAs and not SBAs… but whatever. ūüėõ

I spent what felt like an eternity fusing the jacket pieces. I used weft interfacing on the entire front, collar, facing, then partially fused the back pieces and the sleeves. I also added fusible horsehair on the lapel, upper chest, and the stand area of the undercollar. I had such a hard time with the fusible, and encountered near disaster. First off, the fusing leeched through and stuck to my press cloth so badly that I ended up using parchment paper under my iron. I don’t have an organza press cloth, I was just using muslin, so I don’t know if that would have made a difference.

Then, after fusing, I went to transfer my pattern markings only to find that my pieces had shrunk quite significantly (vertically). I had a mini¬†panic attack and contemplated my options. my longest pieces had shrunk by a solid 3/8″ vertically. Now, I had pre-shrunk my wool, twice actually. I sent it through the dryer on high with a wet towel, then I took our garment¬†steamer to it. I spent quite a bit of time doing this, so I was perplexed as to what had happened. Turns out, it was the fusible that shrunk. Yeah, thanks Pellon. Next time I’ll be ordering from Fashion Sewing Supply. Should I have block fused? Maybe… but to be honest I’m not sure that’s 100% the way to go either. Plus it’s really hard to do well with my current ironing board setup.

Anyways, I had two options: (1.)¬†Sew as if nothing happened. (2.)¬†Go back to my pattern pieces and reduce all the SA’s and re-cut my fabric.

I thought about it for a while and decided that from shoulder to hem, 3/8″ isn’t all that much for a loosely fitted blazer. I had considered shortening the armhole depth, but in the end didn’t, so if I lost 1/8″ there, no big deal. Also, my waist sits high, so a little more length lost there, no big deal. All the fused pieces that had shrunk were going to be sewn to other shrunk fused pieces, so most everything would match up as is.

Okay, freak out over, I started sewing and everything has worked¬†out just fine. Big sigh of relief! As it stands I have the entire shell and facing complete. I should note that I did add a back neck facing piece. It always bugs me when patterns don’t have them, and it’s no work at all to draft.

IMG_4580

I’m very happy with the fit alterations I made from my muslin, everything seems to be working out as expected. I cut a 10 at the shoulder/bust, grading out to a 12 at the hip (for reference, my measurements are: bust 34″, waist 29″, hip 39″). From there I made the following fit adjustments:

  • 1″ SBA (small bust)
  • 1/4″ FSA (forward shoulder)
  • added 1/2″ to the lower part of the back of the armhole (you can check out my pattern alteration¬†in my last post)
  • narrowed the sleeves by 3/8″
  • decreased my SA by 1/8″ from waist to hemline on all the back pieces and the side seams, giving me an extra 1 1/4″ for le booty.

One last thing I need to do is add pockets to the front. I’ve decided to go with patch pockets since, well, I like patch pockets on blazers. I also think I’ll be doing an interior welt pocket. I put¬†one in¬†the winter coat I made two years ago and it’s super handy for phone stashing.

IMG_4575

I finally¬†picked up some lining the other day, so now I’ve got everything I need to finish this baby up. May not get there¬†by the end of November, but it’ll be close!

‚ÄĒlisa g.